repmgr standby register — add a standby's information to the repmgr metadata
repmgr standby register adds a standby's information to
the repmgr metadata. This command needs to be executed to enable
promote/follow operations and to allow repmgrd to work with the node.
An existing standby can be registered using this command. Execute with the
--dry-run option to check what would happen without actually registering the
standby.
If providing the configuration file location with -f/--config-file,
avoid using a relative path, as repmgr stores the configuration file location
in the repmgr metadata for use when repmgr is executed remotely (e.g. during
repmgr standby switchover). repmgr will attempt to convert the
a relative path into an absolute one, but this may not be the same as the path you
would explicitly provide (e.g. ./repmgr.conf might be converted
to /path/to/./repmgr.conf, whereas you'd normally write
/path/to/repmgr.conf).
By default, repmgr will wait 30 seconds for the standby to become available before
aborting with a connection error. This is useful when setting up a standby from a script,
as the standby may not have fully started up by the time repmgr standby register
is executed.
To change the timeout, pass the desired value with the --wait-start option.
A value of 0 will disable the timeout.
The timeout will be ignored if -F/--force was provided.
Depending on your environment and workload, it may take some time for the standby's node record to propagate from the primary to the standby. Some actions (such as starting repmgrd) require that the standby's node record is present and up-to-date to function correctly.
By providing the option --wait-sync to the
repmgr standby register command, repmgr will wait
until the record is synchronised before exiting. An optional timeout (in
seconds) can be added to this option (e.g. --wait-sync=60).
Under some circumstances you may wish to register a standby which is not yet running; this can be the case when using provisioning tools to create a complex replication cluster, or if the node was not cloned by repmgr.
In this case, by using the -F/--force
option and providing the connection parameters to the primary server,
the standby can be registered even if it has not yet been started.
Connection parameters can either be provided either as a conninfo string
(e.g. -d 'host=node1 user=repmgr' or as individual connection parameters
(-h/--host, -d/--dbname,
-U/--user, -p/--port etc.).
Similarly, with cascading replication it may be necessary to register
a standby whose upstream node has not yet been registered - in this case,
using -F/--force will result in the creation of an inactive placeholder
record for the upstream node, which will however later need to be registered
with the -F/--force option too.
When used with repmgr standby register, care should be taken that use of the
-F/--force option does not result in an incorrectly configured cluster.
If you've cloned a standby using another method (e.g. barman's
barman recover
command), register the node as detailed in section
Registering an inactive node then execute
repmgr standby clone --replication-conf-only
to generate the appropriate replication configuration.
--dry-runCheck prerequisites but don't actually register the standby.
-F/--forceOverwrite an existing node record
--upstream-node-idID of the upstream node to replicate from (optional)
--wait-startwait for the standby to start (timeout in seconds, default 30 seconds)
--wait-syncwait for the node record to synchronise to the standby (optional timeout in seconds)
A standby_register event notification
will be generated immediately after the node record is updated on the primary.
If the --wait-sync option is provided, a standby_register_sync
event notification will be generated immediately after the node record has synchronised to the
standby.
If provided, repmgr will substitute the placeholders %p with the node ID of the
primary node, %c with its conninfo string, and
%a with its node name.